Multiple ethernet connection profile in windows 7. Multiple network profiles and switch between them. Add 2 ip adrees to your network. Ip switch Windows 7 - Free Download. The Managed Switch Port Mapping tool maps the physical port connections of a managed network switch to MAC and IP addresses of.

I have no cable or dsl modem and no router. The purpose of the switch is to create a home network, and that's what is not working. A switch by itself does not include all you need to make a well functioning network. You should either have a dhcp server or static addresses as a minimum, even though in your case you should actually be able to communicate with another computer which also gets it address auto-assigned (169.). A dns server is also nice to have to avoid using ip-addresses all the time.

You can get both dhcp and dns in a lot of cheap routers. My Recycle Bin Is Corrupted Vista on this page. Something to consider? To set static ip-addresses: Start ->Run.

->type: ncpa.cpl ->OK ->right click Local Area Connection ->Properties ->Mark Internet Protocol v4 ->Properties On the following page, enter the ip info, i.e.: IP-address: 192.168.0.10 (The last number (10) should be different for every computer or device you connect) Subnet: 255.255.255.0 Gateway: Blank (This would be your router if you had one connected to the internet) DNS 1+2: Blank. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix.: Description...........: Marvell Yukon 88E8056 PCI-E Gigabit Ether net Controller Physical Address.........: 00-24-8C-48-D7-6D DHCP Enabled...........: Yes Autoconfiguration Enabled....: Yes Autoconfiguration IPv4 Address..: 169.254.57.158(Preferred) Subnet Mask...........: 255.255.0.0 Default Gateway.........: NetBIOS over Tcpip........: Enabled It seems your network cable is not connected (possibility of faulty cable) to that switch,.

Your switch doesn't have DHCP-server enabled. Autoconfiguration IPv4 Address shouldn't be 169.254.57.158 it should be: - 10.0.0.0 – 10.255.255.255 - 172.16.0.0 – 172.31.255.255 - 192. Windows Vista Polski Pobierz. 168.0.0 – 192.168.255.255 (often) Try: - connecting it to other port of switch (1-5? Of ports) - be sure not connected to WAN port (it's RJ-45 too?) - using other network cable (no matter if crossover or not) - assigning static ip (look in manual for values) Or your firewall blocks DHCP communication. Maybe you set BLOCK in windows 7 firewall for all outgoing connection? (not sure if it's posible to block DHCP there). Hi, 169.#.#.# is a APIPA (Automatic Private IP Addressing) address; it indicates that the computer was unable to get a valid IP Address. Additionally, I would like to suggest the following: 1.

Manually assign IP address, subnet mask, default gateway and the DNS settings to this network adapter referring to your router’s settings or the good computes’ configurations and check if it works. Update the drive of the network adapter. Boot the computer to Safe Mode with networking to have a check. Unity Quiz Maker.

I noticed you are using a switch, if you have a router, please change the switch with it and see how it works. Hope this helps. Nicholas Li - MSFT.

Hi - thank you both for replying. Here are reponses to your questions and suggestions: Connecting to another switch port: No improvement (the manual says it's RJ-45) Using another cable: No improvement Updating driver: I have had this problem with any driver version installed Safe Mode: No improvement Changing to router: I don't have a router DHCP server: I found no mention of DHCP in the manual at all. It would appear that it is not DHCP enabled. Firewall: Both in and out rules allow DHCP Assigning static IP: I could use some help with this, as I don't know what values to use. If I choose any value from the 192 range as the IP, what do I use for the default gateway and DNS servers? I'm not very knowledgeable about this kind of thing, but I did have this setup working with Vista.